AWCI TECHNICAL MANUAL 12-B PDF

AWCI Technical Manual B, “Standard Practice for the Testing and Inspection of. Field Applied Thin-Film Intumescent Fire-Resistive Materials. Provides field inspection procedures for the testing of thin-film intumescent fire- resistive materials. Includes testing criteria for thickness measurement of applied . AWCI Technical Manual B, Standard Practice for the Testing and Inspection of Field Applied Thin-Film Intumescent Fire-Resistive Materials; an Annotated.

Author: Arashizuru Zolokasa
Country: Azerbaijan
Language: English (Spanish)
Genre: Business
Published (Last): 9 September 2018
Pages: 81
PDF File Size: 9.82 Mb
ePub File Size: 4.59 Mb
ISBN: 909-5-56473-323-3
Downloads: 66417
Price: Free* [*Free Regsitration Required]
Uploader: Faulkree

SECTION ARCHITECTURAL INTUMESCENT FIRE PROTECTION

The following is one example of how a mock-up on a large project might be specified. Materials must be applied in accordance with the project requirements for fire rating thickness, finish texture and color. Provide tdchnical in areas to receive work of this section during application and minimum 24 hours after application. Prior to mixing Part A and B of the adhesive and edge sealant during the installation of the architectural decorative fire protection material, random pre-determined liquid samples of Part A and Part B must be submitted for material characterization fingerprinting in accordance with the procedures detailed in the ISO Standard.

Sequence and coordinate installation of factory-manufactured architectural fire protection system with Work in other sections which would interfere with efficient fireproofing application. In other words, the concrete can’t be too slick or too dry.

Regional Materials- 20 percent extracted, processed and manufactured regionally: Maunal work area from windblown tecynical and rain.

If this location falls within trchnical mile radius of the project site, then Interchar can contribute to earning Materials and Resources Credit 5.

Thickness determinations shall be made at nine locations around the beam, at each end of a in. Others claim that the instructions mean that the sample beam must be tested 12 inches from the end s of the member. International Paint has operations in 54 countries worldwide and over 3, employees. This page can be found at http: Substrate and air temperature shall be in accordance with the manufacturers requirements. Before proceeding with the work, the installer will apply the primer, factory-manufactured architectural fire protection sections and decorative top coat to a representative technjcal section of 10 square feet in size.

  ALAMUT VLADIMIR BARTOL PDF

Do not proceed with remaining work until workmanship, color, and sheen are approved by Architect. A copy of the transport document and manufacturers conformance certificate shall be attached to the material delivery QC form. We have a problem with tchnical that was applied directly over concrete that is now techhical adhesion. Approved by the factory manufactured architectural fire protection material manufacturer and applied in accordance with the topcoat manufacturer’s documented instructions.

The product has excellent corrosion performance and mechanical properties. Sample frequency will be pre-determined by the architect and testing performed by an independent testing laboratory or the factory-manufactured architectural fire protection manufacturer.

Apply technica primer to properly cleaned substrate in accordance with manufacturer’s application instructions.

AWCI’s Construction Dimensions – October 2013

All test results must be made available to all parties at the completion of each pre-designated area and approved prior to the application of top-coat. The relative humidity of the application area shall not exceed a maximum of 85 percent for 24 hours prior, during and 24 hours after the application of the material. Jones is AWCI’s director of technical services.

This section manuap based on the products of International Protective Coatings, which is located at:. Equipment and installation procedures must conform to the factory-manufactured architectural fire protection manufacturer’s installation instructions.

  HONEYWELL R7795A1001 PDF

Submit applicator’s current certification as a manufacturer trained and approved installer.

Technical Manual B

Provide a mock-up for evaluation of surface preparation techniques and application workmanship. To ensure a concrete surface is clean and rough enough to receive a stucco finish, it may need to be sandblasted or mechanically abraded, a dash coat of the cement plaster asci can be applied before the finish coat, or metal lath can be attached using poweractuated fasteners implying a two- or threecoat stucco system to follow.

What could have caused this, and how do we avoid it recurring?

Steel substrate temperature shall be a minimum of 5 deg F 3 deg C above the dew point of the surrounding air for a period of 24 hours prior and during the application of the material. International Protective Coatings is the leading supplier of high performance Protective Coatings and forms part of Akzo Nobel, a market driven, technology based company specializing in Coatings, Chemicals and Pharmaceuticals. Deliver techncial in manufacturer’s original, sealed, undamaged container with identification label intact.

Company specializing in installing the work of this section with a minimum of three years documented experience and certified by the material manufacturer. Once agreed upon in writing, it serves as a guide for the finished work. Requests for substitutions must be made 30 days prior to submittal and contain the full name of each product, descriptive literature, testing 112-b collected from industry consensus standard testing, data on past performance, manufacturer’s instruction for use and generic type.